Exploring Plumbing Fundamentals for Installing a Bathtub
Exploring Plumbing Fundamentals for Installing a Bathtub
Blog Article
Just about every person will have their personal rationale on the subject of A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't exactly brain surgery, but it does require strong plumbing, carpentry, and also in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult task. If the old tub is conveniently accessible, the job can move immediately; if you need to open a wall to eliminate the old bathtub and also place the new tub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will need a helper to vacate the old tub as well as embeded in the new one. Ensure you have qualified on your own for the work as well as fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed project, it is better to think about employing one prior to you start. Chances are you might require an expert plumber to make tube links.
This post will help you set up a brand-new bath tub in your shower room if you have currently gotten a brand-new bathtub and don't require to alter the setup of your previous water supply pipelines.
Your tools and product list ought to comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be rather troublesome due to the limited access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Before moving on to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washing machines remain in area in between the tap as well as the sink. Secure the tap in position with the maker offered backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The previous kind must be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Using both wooden boards under its feet, position the bathtub in the needed placement. The wood boards are practical in evenly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub until the level reviews degree.
To mount taps, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water system and inspect all joints and also new pipework for leaks and tighten them if essential. Load the bath tub as well as also examine the overflow electrical outlet and the normal electrical outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling and also sealing around the bath tub needs to wait up until the bathtub has actually been used at the very least when as this will certainly resolve it right into its last position.
Preparing for the Setup
First of all, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to crack a rigid seal, causing the water to permeate the wall in between the bathroom and the tiling, resulting in issues with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to enable the movement experienced when the tub remains in use. The sealer can crack fairly early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly readily available on the marketplace. It is suggested to fit the tiles using water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on How to Install a Bathtub Yourself? Create a remark below. We'd be delighted to know your views about this write-up. We hope that you visit us again in the near future. Sharing is good. You just don't know, you might be doing someone a favor. Thanks a lot for your time. Come back soon.
Protect your property; contact now. Report this page